ROBOTRON 2084 - Scratch Built Replica

[scr33n]

Tweet

It's happen, another time  .... unfortunately   I've found the pieces for another great game and cab (on my wish list):



I can't resist, so another scratch built replica is around the corner...

I'm not sure.... anyone here in europe owns this cab? I don't know, I try to ask your help here and on klov.

Let's start with some measures:




























thanks to anyone who can help me!!!  

two packages are already flying over the ocean ... fingers crossed ... as always  

[baritonomarchetto]

I cannot help, but for sure will follow your project... as always!

[DarthNuno]

Cannot help this time, but I'm really happy to follow a new 'Scratch Built Replica' story by Scr33n 

[Luigi]

So you're interested in building the us-version or the european? I've got the european version and I've already painted a CPO for it.

Let me know and I will try to get the measures you want asap

[scr33n]

So you're interested in building the us-version or the european? I've got the european version and I've already painted a CPO for it.

Let me know and I will try to get the measures you want asap

Thanks Luigi but it's the US version 

[Luigi]

No problem....good luck with your project!!

[R64]

Great! I'll watch with interest. This guy didn't have much luck getting measurements, but his email's there maybe he got them eventually?

http://forum.arcadecontrols.com/index.php?topic=74412.0

[Luigi]

Now that guy is really annoying....instead of grabbing the reached hands (people offered to measure their cab) he keeps whining for a complete set of plan......tz.....

[scr33n]

I obtained these measures from a Klov member (LongJohns):

In mm

1 = 1782
2 = 1630
3 = 218
4 = 724
5 = 724
6 = 94
7 = 28 *see note 1
8 = 25 *see note 2
9 = 236
10 = 164
11 = 884
12 = 10
13 = 15
14 = 45
15 = 7
16 = can't measure as cabinet stripped
17 = 200

*note 1 - subtract marquee thickness. Also this measurement is in the center - the marquee is mounted at an angle. 40 mm down from the top it is 31 mm to the front edge (less plexi thickness), and @ 185 mm down from the top it is 25 mm from the front edge (less plexi)

*note 2 - also less thickness of the bezel and also measured in the center as it follows the same angle as the marquee. Hard to measure without multiple measurements as the cabinet curves here.

 

[scr33n]

Other measures (thanks to LongJohns on Klov  ):




























in mm

18 = 38
19 = 70
20 = 150
21 = 50
22 = 34
23 = 70
24 = 70
25 = 150
26 = 50
27 = 70
28 = 660
29 = 625
30 = 680 from the front flat plane
31 = 1450 to the center of the curve
32 = 520 from the center of the curve @ bottom to the front face flat plane (where the curve starts)
33 = 208 from the flat planes on each end
34 = 602 (fairly sure on this, but hard to be 100% as I still have that part of the cabinet masked off for painting)
35 = 598

width of the upper door is 620

Planning can start ...

[scr33n]

First package from Quarterarcade is here:



inside:




- williams 2 slot coin door
- williams lower coin door
- new repro marquee
- original robotron speaker panel + speaker (great conditions!!!)
- coin door bolts

 

[Luigi]

I've got two wheels and two legs incl. mounting plates. I bought them new from Arcadeshop.de but since the derusting was so successful I decided to use the original stuff instead. Let me know if you're interested for a good price......I could bring them to EC


Why two legs only: it's hard to move a cab when it's sitting on 4 feet. I'd rather put it on two feet in the front and the two wheels in the back. So you can simply lieft the front and pull it towards you

[scr33n]

Another package from US (arcadeboneyard):



inside:



 

[scr33n]

Two other packages from US ...

first one from a Klov member (robotron911 - thanks Mark!!!):

inside:




- nice original and clean Robotron control panel
- CP hinge
- rear lower door hinge
- 2 nos wico 4" joysticks 
- 4 translucent blue long buttons (not work with this control panel  )

and from Arcadeshop.com:



inside:




- Robotron CPO repro
- CP hinges repro
- CP molding trim
- 2 translucent blue short buttons (works with this control panel  )
 

another package from Gamestencils.com (for the stencils  ) and I'm ready to go .... 

[Muerto]

 
Cant wait for the next step!!